Recently I made a LEGO race car with a driver who wore a helmet. Unfortunately, after the race, I tried to take off his helmet and his head came off inside the helmet. Any suggestions about getting it out so he can see again?
You can use some sugar liquid to use as temporary glue to make the head stuck to the torso. Then wait till the sugar is sticky and then try to remove the helmet. Once the helmet is loose you can put the head and torso in warm water to loosen the sugar glue and take it off. Then wash thoroughly to remove remaining sugar.
A trick that's worked for me in the past, is to use a 1x1 cone with a Technic axle in it (it needs to be the cone without the top groove, unlike the example below) - this will allow you to force the tapered end of the cone into the hole on the bottom of the head, and by fastening a Technic gearwheel, brick or larger cylinder to the Technic axle, you'll be able to ply a fair amount of force to increase the clutch of the cone piece in the head and twist to loosen it from the helmet with a push-twist-pull movement. Good luck.
Your problem is that the clutch (what holds bricks together) between the helmet and the head is too high, and in any case higher than the clutch between head and torso.
This means the solution is to increase the clutch between the head and another part you'll use to remove it. I would first recommend trying other torsos, maybe one has enough clutch to easily take the head with it and beat the helm. Twisting the parts while trying to separate them should also help.
If that fails, other LEGO parts might help, but I'm not sure which ones - torsos have a longer stud probably for that very reason. Maybe a Technic pin with friction?
You could also try slipping some paper around a torso stud, but be careful not to just push the paper alone inside the head.
A quick and easy way to remove a helmet stuck onto the head...I tried something similar to the toilet tissue paper idea above. I used a piece of Bounty kitchen roll, approximately 3cm x 3cm, (which is actually thicker then a single ply toilet tissue) and placed this over the stub of the body then pushed the head onto this. The head will not go all the way down, but far enough for it to remain firmly in place. Then I was able to remove the helmet very easily.
You need to get something into the head-hole to grip the head whilst you remove the helmet.
You could try a pair of snap-ring pliers or needle nose pliers. Insert both jaws into the hole and pull them apart as much as possible whilst you remove the head from the helmet. You might need a helper - someone to remove the helmet whilst you grip the head with the tool.
You may not be able to avoid scratching the inside of the head-hole slightly - but a scratch where it won't be seen is probably better than throwing two parts away.
Worst case, you write-off the head completely, but at least you've still got a useful helmet. If you do get to the point where you can't remove the helmet without damaging it, you could resort to super-gluing something to the inside of the head and pull it out.
I just removed a non-LEGO crown which was very very tight top on Nadakhan's head. It was so tight, it seemed that only destroying it could help. But my son loved the crown and especially head, so here is my solution:
- I put some olive oil between the crown and the head
- I took a paper napkin and put it over a LEGO torso's neck
- I put the head stuck on the neck over the paper, so the head was pretty tight on the torso
- I boiled some water, poured it into a cup, then holding the minifigure's legs, put the crown in the boiling water. Please note - not the head, just the helmet (crown in my case)!
- After about 2 minutes held in the very hot water (I hoped the hot water would expand the crown, but not the head. I don't know if this step was really necessary), I could completely remove the crown from the head with pliers.
Good luck to everyone with the same problem :)
You should try to use a torso that is really, really gripping. The newer, the better. Do you have any Exo-Force minifigures? I found those torsos really, really tight. Whenever I got something stuck, I always plonk them on Hikaru's torso. Works most of the time. Helps if you twist it around. Once the helmet turns but the head doesn't, you're gold.
Take a household screw slightly wider than the hole inside the head. Screw it in until the threads feel a bit tight. Then pull it out with a pliers. If you have a screw but it's not wide enough inside the neck, wrap it in a paper towel and screw it in till it's tight and will make the head turn inside the helmet, and then pull it out.
You can also try to use soapy water. You know how people use soap to remove a stuck ring from their finger? The same works for stuck LEGO helmets. Just immerse the helmet/head in some water with lots of soap, then do as Joubarc mentioned; attach them back to a torso, and now wiggle off the helmet...(c:
Take a piece of tape, Put it around a torso neck cut it until about half of a centimeter is still above the top of stud. Now force the head with stuck helmet on it. Pull on the helmet and it will come off! To get the tape off the torso use pliers or your fingers to grab the bottom and pull upward until it comes off.