Questions tagged [ev3]

EV3 is the current generation of LEGO MINDSTORMS, released in 2013.

Filter by
Sorted by
Tagged with
2
votes
1answer
165 views

How can I get the EV3 to control an ordinary motor with PWM?

Looking at the hardware developer pdf, it looked like the EV3 should output a PWM signal with a duty cycle corresponding to power level. It does, but only for 100ms and only on pin 1. Is that how the ...
2
votes
1answer
101 views

What kind of mat do you use for running Mindstorm EV3?

Turning Ev3 precisely has been a problem. Do you use a mat for running EV3 on. Can you tell me on what material to get the mat printed?
2
votes
1answer
482 views

What is a better algorithm for wall following with an ultrasonic sensor?

This wall following algorithm uses the ultrasonic sensor. It has a horrible worst case behavior. Place the robot about 3 cm too far from the wall. Instead of moving closer to the wall, the robot ...
2
votes
1answer
827 views

Can't create block: “Use of a block which no longer exists”

Unable to compile some documents for deployment: Program.ev3p: Use of a block which no longer exists. PutInRange.ev3p The block i want to make. It will put a input value inside a given range. When i ...
2
votes
2answers
273 views

EV3 isn't showing up in programming software after pairing on Windows XP

Running Windows XP x32. I've connected, paired, connected, paired, paired, and connected, but I just can't get the EV3 software to recognize my EV3! I've used this EV3 before on a different PC over ...
2
votes
1answer
194 views

EV3 motor control proportional to another motor when more than two motors

From what I understand, in EV3-g you can use "move steering" or "move tank" blocks to regulate two motors proportionally to each other as they have a built-in PID controller to do that. If one motor ...
2
votes
1answer
247 views

EV3 switch block does not recognize text?

i am using file access to input variables into my programm. text file is something like this: a b c .. on each loop, program access file (using File Access block) and reads a new line "a" or "b" or "...
2
votes
1answer
141 views

Do we need WiFi Dongle to install Scratch on EV3

I was wondering if I can install Scratch program on EV3 brick without the wifi dongle. Appreciate any insight here.
2
votes
1answer
4k views

EV3 won't connect through bluetooth anymore

I was using VS2015 (C#) to write simple programs for my EV3 using a bluetooth connection. This was working fine for several days and then suddenly stopped. I can't for the life of me figure out why. ...
2
votes
1answer
464 views

Controlling EV3 motors within VC++

I've got an application within some VC++ software (BCI2000). This is running on Windows 7. Although BCI2000 can run elsewhere, I'd like to stay on Windows. I've got an EV3 whose motors I'd like to ...
2
votes
1answer
47 views

Cannot add instruction tiles to EV3 brick program.

I was using the EV3 brick program software included in the ev3 Brick and I can no longer add instructions. I think I've reached the max length. Is there a way around this? Can I run a second program ...
2
votes
1answer
265 views

EV3 Programme won't load to brick

I have installed EV3 on my PC and am trying to load a program into an NXT 1 Brick. When I click the down load button on the EV3 screen the Brick beeps twice and the program does not load. What am I ...
2
votes
1answer
2k views

usage of ev3 ultrasonic sensor in lejos behavior based programming

I'm using ev3 ultrasonic sensor. And I'm writing a behavior based lejos code. I want to do some tasks when the ultrasonic sensor detects an object which is not further than 30 cm's. And this is my ...
2
votes
1answer
216 views

Tufts MAZE LabView Program Will Not Run on EV3

Through the 2012 LabVIEW for LEGO software package, I found an example of a maze from Tufts. I cannot get it to run on an EV3. It appears to just constantly execute the initialization. How can I ...
2
votes
1answer
774 views

How can I use bluetooth on my phone to run a program on the EV3 brick?

I tried the Commander app but it seems to just let you control individual motors. I would like to run the various programs I have made using an input on the phone through Bluetooth Is this possible ...
2
votes
1answer
1k views

Trouble with Commander app: Using buttons to control motors

I'm having trouble with the Commander app for Android. I've put an EV3 into set 8448. I'm using one of the large motors for propulsion and a medium motor for rack and pinion steering. I don't have the ...
2
votes
1answer
478 views

Lego EV3 doesn't respond to direct command

I tried to execute command (via bt) play tone: play_tone = '\x0F\x00\x00\x00\x80\x00\x00\x94\x01\x81\x02\x82\xE8\x03\x82\xE8\x03' # send commands to EV3 via bluetooth with open('/dev/tty.EV3-...
2
votes
2answers
381 views

Is the NXT forward compatible with EV3 sensors and motors?

Is it possible to use EV3 sensors and motors with the NXT intelligent brick? I've read that the EV3 is backward compatible with NXT motors and sensors, but does vice versa work as well? Is the NXT ...
2
votes
0answers
37 views

Improving EV3 Screen Readability

I often have a hard time reading the EV3’s LCD display. I presume that I’m not the only one who has experienced this issue. Is there a way to improve its readability? For example, are there any good ...
2
votes
0answers
116 views

How many rotations or degrees do you need to turn your robot?

I have an EV3 Home edition. I have made a tribot. Two main motors for the wheels and a caster in the back. To complete a full turn in place I need to set the rotations to 2.32 or 835 degrees. Does ...
2
votes
0answers
345 views

Lego EV3 simulator and programming

I've been searching and testing for hours. There is little information on this subject though. I have some specific requirements for a Lego EV3 simulator and programming environment. I do not want to ...
2
votes
1answer
277 views

Lego mindstorms ev3 spinner factory problem

I hope you can help me with this. I'm on an education where we practice all stuff about IT. I'm currently working on the Spinner Factory project in the EV3. However, when i looked through the program ...
2
votes
0answers
308 views

Is there an leJOS simulator for EV3?

I found this but this seems to be using their own library to control the EV3.
2
votes
0answers
33 views

Is my EV3 controller bricked? [duplicate]

My EV3 controller seems to be 'stuck' in this state: Is the device operating properly? If not, is there a procedure that can unbrick the controller? Thank you
2
votes
0answers
549 views

Programming NXT ultrasonic sensor with EV3 software [closed]

How can I program the NXT ultrasonic sensor with EV3 software? When I pick the block for the ultrasonic sensor, it tells me it is not compatible.
2
votes
0answers
1k views

Bluetooth connection to EV3 from Java on Linux/Android

I would like to connect to my EV3 from PC (and then Android) via Bluetooth. I was able to connect to NXT with LEGO-MINDSTORMS-MINDdroid which uses direct LCP commands but as far as I know the ...
2
votes
0answers
634 views

Sending Gcode to LEGO mindstorms x/y plotter?

I am building an x/y plotter out of LEGO Mindstorms. I would like it to read an SVG file on the EV3 brick, convert it to gcode, and draw the coordinates. How would I go about doing this?
2
votes
0answers
356 views

How to determine orientation of a EV3 gripper?

I have built the EV3 Gripper using the manual. I am programming an ev3 brick using ev3dev. I need to determine the angle/direction/orientation of the robot programmatically, before I can issue a ...
2
votes
0answers
91 views

HiTechnic Color Sensor analog

HiTechnic sales support said that HiTechnic color sensor hasn't been manifactured yet. Currently it's out of stock in HiTechnic shop. Is there any analog of this sensor except NXT/EV3 color sensors?
2
votes
0answers
334 views

What are the steps in installing the EV3 block developer Kit?

I've downloaded the block developer kit. How do I incorporated into my Mindstorms software?
2
votes
0answers
138 views

Unable to turn on the EV3

I just can not turn on the EV3 with the SD card. I only turned on it twice. The EV3 stops at [-leJOS EV3] UI and does not go to the next step. I charged the battery, reinstalled the software inside ...
2
votes
1answer
1k views

EV3 with NiMH batteries

Could I use 6 NiMH 1.2V batteries and keep pressed the small black circle in the battery compartment in order to adjust the battery gauge and low battery alarm?
2
votes
0answers
384 views

How do I control one EV3 using another through bluetooth and LabVIEW?

I have LabVIEW 2014 and I'd like to control make one EV3 move forward using another through bluetooth using LabVIEW, and I don't want to have to use the computer as a relay. How do I do this?
2
votes
2answers
428 views

Inverting motor's rotation

I've designed a robot with two motors. It works as follows: The first motor is attached to the the person's arm, the second motor receives the calculated movement and moves accordingly. When the ...
2
votes
0answers
205 views

After adding a MyBlock icon to the EV3 palette of MyBlock icons, how can the new icon be associated to an existing MyBlock?

After following the advice given in adding a MyBlock icon to the EV3 palette, can the icon be associated to an existing MyBlock? Something better than copy/paste the contents of the existing MyBlock ...
2
votes
1answer
373 views

Good EV3 iBook for programming or building

I am a participant in a Lego mind storms competition soon using EV3. I would like to know if there are good, free iBooks for me to download (PDF or iBook from the apple iBook store). Preferably the ...
2
votes
1answer
454 views

Does NXC work with EV3? [duplicate]

Is it possible to create and run NXC programs on the EV3 brick? I installed BrixcCC, created a simple Hello World NXC program and selected "Download and Run" in the Compile menu. The EV3 brick made ...
2
votes
0answers
167 views

Is the EV3 brick balanced? [closed]

I want to buy an ev3 but I want to know if the center of gravity is off in the brick (really does not look symmetric)
1
vote
1answer
107 views

Why does display output affects motors?

I'm making a simple program with LEGO EV3 Education. It makes a little tank to follow a black line over a white-ish floor. Here it is: [] This works very smooth: it makes the tank follow the EDGE ...
1
vote
2answers
90 views

What does this symbol on the EV3 Brick mean?

I can’t figure out how to get my R3PTAR to open and close it’s mouth to bite. I keep getting this symbol. What does it mean?
1
vote
2answers
593 views

Programming with Lego Mindstorms EV3

I know this question was asked in the past, but I want an up-to-date answer. What is the best way to program with the NXT with a oriented object programming language? Ideally C#, C++ or Java (maybe ...
1
vote
1answer
56 views

How to make of point coordinate system for EV3

I'm trying to make a internal coordinate system for an EV3 Python project I'm doing, but at a complete loss on how to do it. It needs to keep track of how it moves (with wheels) in an X, Y coordinate ...
1
vote
1answer
273 views

Why do I not have the Brick Datalog app in the LEGO Mindstorms EV3 V1.10E firmware?

I realize a similar question has been asked (you can view it here) however mine is slightly different. I have a Lego Mindstorms EV3 Home Set 31313 and due to recommendation, I installed Lego ...
1
vote
1answer
40 views

Can I install EV3 Education software and Retail software side by side?

I have EV3 Retail edition and I like to buy required sensors and build the robots come with the education edition of EV3. I have lots of LEGO Technic spare parts so I expect I can find alternate parts ...
1
vote
1answer
120 views

EV3 Ultrasonic Sensor (45504)

I leanred that EV3 Ultrasonic Sensor (45504) is out of stock for a long time. I wonder if the sensor is being discontinued due to accuracy problem? Is there any alternate version of "Gyro Boy" that ...
1
vote
1answer
86 views

How to use the direct command to make ev3 motor backward?

I write the java language. I use ev3 direct command make ev3 motor to run, example: "opOUTPUT_POWER,LC0(0),LC0(0x01),LC0(20), opOUTPUT_START,LC0(0),LC0(0x01)" In this case, the power is 20 so I ...
1
vote
2answers
691 views

“Unable to compile” error code with LEGO EV3 Arm Robot Program

Does anyone know how to fix this error with my LEGO EV3 program? Unable to compile some documents for deployment: Program.ev3p: Use of a block which no longer exists. INI.ev3p: A My Block cannot ...
1
vote
1answer
190 views

Why does my EV3 not have data logging in Brick App menu?

I recently purchased a 45544 Educator Mindstorms product. In working through tutorials. I am at section on data logging, but my Brick Apps menu stops at Brick Program. Data Logging is not on menu My ...
1
vote
1answer
712 views

Raw sensor question?

What is raw sensor and what is on port 3? Is this code only for robot to go completely straight without errors?
1
vote
1answer
2k views

Where can I find a good tutorial on programming with Lejos?

I want to get started with LeJOS and use Java to check to see if an EV3 touch sensor is pressed, but I can't find any decent tutorials. Are there any good resources for this?